Skip to main content
Application

Application guide for PropOne

Please see our multilingual brief application guides, technical datasheet or application video or step-by-step guide below for application instructions:

You can also reach out to one of our PropOne accredited applicators. Accredited applicators are trained and supported by both Greencorp Marine and their local distributors. Should you wish to find an accredited applicator in your local area, please contact us and you will receive a list of applicators in your area.

You can also contact a local boatyard or dealer in your area to apply it for you.

Estimated Coverage Guide:
Propeller Size and Number of Blades

18″- 24″ 24″- 36″ 36″- 48″
Three or four blades Four or five blades Five blades
Running gear components to be painted One propeller 250mL Kit 500mL Kit 500mL Kit
Two propellers 250mL Kit 500mL Kit 1 Litre Kit
Two propellers, two rudders
two propeller shaft struts
500mL Kit 500mL Kit 1 Litre Kit
Two propellers, two rudders, two propeller shaft struts & two trim tabs 500mL Kit 1 Litre Kit 1 Litre Kit
Application Video
Step One

Surface

Preparation

Step Two

Surface

Cleaning

Step Three

Primer

Application

Step Four

Clear Coat
Application

  • Remove marine growth & existing coatings from metal surfaces.
  • Abrade the metal with a mechanical grinder, wire wheel or by hand sanding (80-120Grit).
  • For newly polished/repaired metals, abrade the metal surfaces to remove any slight surface oxidisation.
  • Rinse metal surfaces with clean fresh water, ensuring that any abrasive residue is fully removed.
  • Apply Prop Wash using a clean cloth to scrub the surface. Do not allow to dry.
  • Rinse the surface with clean fresh water and wipe with a clean damp white cloth.
  •  Repeat until the cloth shows no discolouration.
  •  Solvent wipe metal surfaces with acetone using a separate clean cloth.
  • Keep metal surfaces dry and free from contaminants, do not touch surface.
  • Mix Primer for 3 minutes until solids are dispersed. Then pour Activator slowly into Primer whilst stirring, mix for 3 minutes. Replace lid and shake can for 2 minutes.
  • Using a new brush or roller, apply at least 1 thin coat of Primer, preferably 2 thin coats.
  • Ensure complete coverage of the metal surface is achieved.
  • Allow Primer to touch dry between coats.
  • Do not apply a thick coating.
  • To prevent runs, apply out to the blade edges.
  • As soon as Primer is touch dry apply the Clear Coat.
  • Apply 1 generous coat of the Clear Coat using a new brush.
  • To prevent runs, apply out to the edges and avoid scraping brush or roller on blade edges.
  • Do not touch or immerse in water for 12 hours.

Questions? Check out our FAQ section or don’t hesitate to contact us.

Step One

Surface

Preparation

  • Remove marine growth & existing coatings from metal surfaces.
  • Abrade the metal with a mechanical grinder, wire wheel or by hand sanding (80-120Grit).
  • For newly polished/repaired metals, abrade the metal surfaces to remove any slight surface oxidisation.
  • Rinse metal surfaces with clean fresh water, ensuring that any abrasive residue is fully removed.
Step Two

Surface

Cleaning

  • Apply Prop Wash using a clean cloth to scrub the surface. Do not allow to dry.
  • Rinse the surface with clean fresh water and wipe with a clean damp white cloth.
  •  Repeat until the cloth shows no discolouration.
  •  Solvent wipe metal surfaces with acetone using a separate clean cloth.
  • Keep metal surfaces dry and free from contaminants, do not touch surface.
Step Three

Primer

Application

  • Mix Primer for 3 minutes until solids are dispersed. Then pour Activator slowly into Primer whilst stirring, mix for 3 minutes. Replace lid and shake can for 2 minutes.
  • Using a new brush or roller, apply at least 1 thin coat of Primer, preferably 2 thin coats.
  • Ensure complete coverage of the metal surface is achieved.
  • Allow Primer to touch dry between coats.
  • Do not apply a thick coating.
  • To prevent runs, apply out to the blade edges.
  • As soon as Primer is touch dry apply the Clear Coat.
Step Four

Clear Coat
Application

  • Apply 1 generous coat of the Clear Coat using a new brush.
  • To prevent runs, apply out to the edges and avoid scraping brush or roller on blade edges.
  • Do not touch or immerse in water for 12 hours.

Questions? Check out our FAQ section or don’t hesitate to contact us.